Piston Pin Support Plate The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1164.pdf FITS Harley Davidson EL 1936 Harley Davidson EL 1937...

Primary Locking Tool The Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torquing of clutch hub and engine nut. FITS Harley Davidson FXD 2006 Harley...

Receptacle Extractor Tool for Molex Style Connector Receptacle extractor tool removes Molex style connector

Right Side Case Race .005 .005 oversize right side case race is machined and ground to factory specifications. FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley Davidson G 1942 Harley Davidson G 1943 Harley...

Right Side Case Race Standard Standard right side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch . FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley...

Rocker Arm Bushing and Roller Bearing Puller This rocker arm roller bearing puller Instructions: http://www.vtwinmfg.com/Instructions/16/16-1848.pdf

Rocker Arm Bushing Reamer Tool The Jims rocker arm bushing reamer tool is used to ream rocker bushings to a factory fit of .0007 inch-.0012 inch in line with each other. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1804.pdf

Rocker Arm Shaft Jims rocker arm shaft has an outer diameter at the big end of .937 inch and the small end of .434 inch. Measurements: Outer Thread Pitch: 7/16 inches -20 FITS Harley Davidson FL 1966 Harley Davidson FL...

Shaft Turning Tool This Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2 inch ratchet or impact driver. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1378.pdf FITS Harley Davidson FLST 2007 Harley Davidson FLST 2008...

Shoulderless Valve Guide Driver Tool Handle Only Use driver handle to remove or install valve guides. Installation of shoulderless guides requires correct installation socket. Tech Notes: Recommended to use with #16-0321 Valve Guide Installer Tool FITS Harley Davidson FLST 1999...

Shoulderless Valve Guide Installer Tool Remover handles are used as handle for installer tool must be ordered separately. Use driver handle to remove or install valve guides. Installation of shoulderless guides requires correct installation socket. Tech Notes: Recommended to use...

Snap Ring Remover Tool You can replace the snap ring in Big Twin cases without the fear of gouging the aluminum on the cases. FITS Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley Davidson FLST...

Solid Tappet Assembly .005 Order adjuster screws and nuts separately. FITS Harley Davidson FL 1948 Harley Davidson FL 1949 Harley Davidson FL 1950 Harley Davidson FL 1951 Harley Davidson FL 1952

Solid Tappet Assembly .005 Jims .005 oversize solid tappets can be only used with adjustable pushrods. FITS Harley Davidson XL 1986 Harley Davidson XL 1987 Harley Davidson XL 1988 Harley Davidson XL 1989 Harley Davidson XL 1990 Harley Davidson XL...

Sprocket Flywheel Nut Socket Tool Jims sprocket flywheel nut socket features a low profile to give 100% nut contact machined flat at nut receiving end to eliminate rounding off the nut. Fits 3/4 inch Drive. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1812.pdf FITS Harley Davidson...

Sprocket Shaft Bearing and Seal Installation Tool Adapter Allows for installation of Timken bearings and roller bearing race assembly onto the sprocket shaft. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1364.pdf FITS Harley Davidson FLST 2007 Harley Davidson FLST 2008 Harley Davidson FLST 2009 Harley Davidson...

Sprocket Shaft Bearing Installer Tool Tool is 2.500 inch long. Tech Notes: Required to use with #16-1761 Sprocket shaft bearing installation tool FITS Harley Davidson XL 1977 Harley Davidson XL 1978 Harley Davidson XL 1979 Harley Davidson XL 1980 Harley...

Sprocket Shaft Bearing Installer Tool This tool also can be used to install the bearing until tool runs out of threads. Tool is 2.060 inch long. Tech Notes: Required to use with #16-1760 sprocket shaft bearing installation tool Instructions: http://www.vtwinmfg.com/Instructions/16/16-1761.pdf...

Sprocket Shaft Bearing Tool *NOTE: Includes 1 collar. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1836.pdf FITS Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley Davidson FL 1959 Harley Davidson FL 1960 Harley Davidson FL 1961 Harley...

Sprocket Shaft Bearing Tool If using this tool on a 1977-up XL we require using the 2.500 inch and 2060 inch sprocket shaft bearing installer tool. Tech Notes: Required to use #16-1760 2.500inch Sprocket Shaft Bearing Installation Tool on 1977-up...

Sprocket Shaft Nut Jims sprocket shaft nut is 1-1/8 inch-16 for taper end shaft. FITS Harley Davidson FL 1972 Harley Davidson FL 1973 Harley Davidson FL 1974 Harley Davidson FL 1975 Harley Davidson FL 1976 Harley Davidson FL 1977 Harley...

Sprocket Shaft Seal and Lock Installer Sprocket shaft seal wrench tool installs and removes bearing nut on Big Twin models. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0888.pdf FITS Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley...

Sprocket Shaft Seal Install Tool Use with a bearing tool to help install seal. Tech Notes: Order #16-0140 or #16-1836 bearing tool Instructions: http://www.vtwinmfg.com/Instructions/16/16-1754.pdf FITS Harley Davidson FL 1970 Harley Davidson FL 1971 Harley Davidson FL 1972 Harley Davidson FL...

Standard Case Race Left Side Left side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch. FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley Davidson G...