Jims M8 Primary Locking Tool Jims primary locking tool is used to lock the primary for service work on M8 models. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST 2021 Harley Davidson...

Shock Adjuster Tool Replica shock adjusting tool FITS Harley Davidson FLT 1979 Harley Davidson FLT 1980 Harley Davidson FLT 1981 Harley Davidson FLT 1982 Harley Davidson FLT 1983 Harley Davidson FLT 1984 Harley Davidson FLT 1985 Harley Davidson FLT 1986...

Spark Plug Wrench Tool Spark plug wrench 14mm

Primary Plug Wrench Primary plug wrench FITS Harley Davidson XL 1971 Harley Davidson XL 1972 Harley Davidson XL 1973 Harley Davidson XL 1974 Harley Davidson XL 1975 Harley Davidson XL 1976 Harley Davidson XL 1977 Harley Davidson XL 1978 Harley...

Gasket Locator Tool This Jims 3 piece gasket locator tool will properly align the primary cam and transmission end cover gaskets that will prevent misalignment and oil leaks.

Flywheel Locking Tool The flywheel locking tool screws into the timing hole and allows the holding of the crank for top dead center. It has a hollow center to allow viewing of timing mark.

Jims M8 Balancer Bearing Installer Tool All M8 engines incorporate balancers to reduce vibration. This tool has been developed to be used with the balancer bearing removal tool 16-5832* to precisely install the bearings in the proper location. This installation...

Combo Engine and Transmission Lapping Tool Combo lapping tool is used to lap right and left crankcase races for oversized bearings and is used to insure proper fitting of oversized rollers with mainshaft races. Rod laps are not included. The...

13 in 1 Folding Tool Kit This tool includes: 3-Hex: 5/32 - 3/16 - 1/4 inch 2-Torx: T25-T27* 2-Screwdriver: 205* 2-Open Wrench: 10mm - 12 point box 9/16 open end - 6mm spoken wrench 3-Socket: 3/8 - 7/16 - 1/2...

Sprocket Shaft Bearing Nut Wrench Tool Sprocket shaft bearing nut wrench tool installs nut and seal. FITS Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley Davidson FL 1959 Harley Davidson FL...

Sifton Wrist Pin Bushing Reamer Tool Order rod clamping tool separately. This tool is used to secure the rod while performing the reaming operation. The front of the taper is .767 inch body for actual reamed hole is .792 inch....

45 W-WL-WR-G Parts and Service Manual *NOTE: Includes WR factory data completed WL parts book early to late number conversion pages V-Twin 45 replacement parts and service index. **NOTE Product may not be returned. ISBN: 978-1-7327387-1-3 1st edition. ISBN: 978-1-9503220503...

1930-1965 Linkert Carburetor Parts Book ISBN: 978-1-950322-08-4. **NOTE: Product may not be returned. FITS Harley Davidson FL 1930 Harley Davidson FL 1931 Harley Davidson FL 1932 Harley Davidson FL 1933 Harley Davidson FL 1934 Harley Davidson FL 1935 Harley Davidson...

Valve Spring Compressor - 18/24 mm Quick-release system presses straight against the retainer to eliminate side-loading the valve and keepers while not damaging or scratching valves, Works on all motorcycle, ATV, UTV, and small engine cylinder heads, Fully adjustable top...

Dowel Puller - 17 mm To be used in conjunction with Dowel Pin Puller Set (sold separately), Designed to assist in pulling stuck dowel pins from engine cases

Heim Joint Tool - Alignment/Installation - KTM/Husaberg Handle includes retention O-ring to hold heim joint adapters and heim joint bearing in place, Removes and replaces KTM heim joints or aftermarket equivalents, Built in stop correctly centers heim joint in swing...

Fork Seal Driver - Ringer® - 35-36 mm Locking ring features knurled finish for secure no-slip grip and positively locks body halves together during use, Innovative design makes tool easier and more secure to use than old-fashioned pin-aligned drivers, High...

Fork Seal Driver - Ringer® - 39 mm Locking ring features knurled finish for secure no-slip grip and positively locks body halves together during use, Innovative design makes tool easier and more secure to use than old-fashioned pin-aligned drivers, High...

Fork Seal Driver - Ringer® - 45 mm Locking ring features knurled finish for secure no-slip grip and positively locks body halves together during use, Innovative design makes tool easier and more secure to use than old-fashioned pin-aligned drivers, High...

Fork Seal Driver - Ringer® - 48 mm Locking ring features knurled finish for secure no-slip grip and positively locks body halves together during use, Innovative design makes tool easier and more secure to use than old-fashioned pin-aligned drivers, High...

Damping Rod Holder - Inner Fork Cartridge Holds damping rod for inner fork cartridge removal, Fits damping rod diameters of 10 mm to 14 mm, Anodized finish with laser engraving, Lifetime limited warranty

Combo Lever - T6 - Hex - 30 mm - 10/12 mm - Set One lever has unique combination stepped 10/12 mm box end wrench on other end for turning rim lock nuts, Tire spoon with axle nut hex wrench...

Socket - Fork Cap - 39 mm Machined from 6061-T6 aluminum with durable blue anodizing and laser engraved markings, Use for removal and installation of the fork cap nut (1-3/8" hex), Thin socket measures only 9/32" deep and 5/8" tall,...

Combo Lever - T6 - Hex - 27 mm - 10/12 mm - Set One lever has unique combination stepped 10/12 mm box end wrench on other end for turning rim lock nuts, Tire spoon with axle nut hex wrench...