Fork Spring Compressor Tool Compressor can be mounted in a vise for easy hands free servicing. Tool includes an adapter for FL forks to elminate direct contact with spring coil and a special rod to pull up the fork damper...

Fork Tube Plug Tool This Jims fork tube plug tool is used to remove and install top fork tube plugs. Eliminates possible burring of plug caused by wrenches. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1008.pdf FITS Harley Davidson FL 1948 Harley Davidson FL 1949 Harley...

Gasket Locator Tool This Jims 3 piece gasket locator tool will properly align the primary cam and transmission end cover gaskets that will prevent misalignment and oil leaks.

Hydraulic Tappet Assembly .005 Order hydraulic unit and nuts separately. **NOTE: Tappet adjustment will make the pushrod tight. Wait 5-15 minutes or longer to fully bleed off the hydraulic tappet. Make sure engine is not rotated while pushrods are tight....

Hydraulic Tappet Assembly .005 Jims big axle power glide hydraulic tappet only is .005 inch oversize for Shovelhead engines. Instructions: http://www.vtwinmfg.com/Instructions/10/10-0644.pdf FITS Harley Davidson FL 1966 Harley Davidson FL 1967 Harley Davidson FL 1968 Harley Davidson FL 1969 Harley Davidson...

Inner Primary Cover Bearing and Seal Remover Installer Tool Also removes and installs inner primary and seal that the transmission mainshaft passes through. FITS Harley Davidson FLHT 1985 Harley Davidson FLHT 1986 Harley Davidson FLHT 1987 Harley Davidson FLHT 1988...

Jims 1-Hole Crank Pin Jims crank pin features heat treating 60-62 RC to a case depth of .100. Threads are inchJ inch type. Crank pin is stepped and is 1 oil hole type. FITS Harley Davidson FL 1940 Harley Davidson...

Jims 3-Hole Crank Pin Jims crank pin features heat treating 60-62 RC to a case depth of .100* threads are inchJ inch type. Crank pin is 3 oil hole type and measures 3-7/8 inch. Measurements: Outer Diameter: 1.254 inches FITS...

Jims 3-Hole Crank Pin Order nuts separately. FITS Harley Davidson FL 1981 Harley Davidson FL 1982 Harley Davidson FL 1983 Harley Davidson FL 1984 Harley Davidson FLT 1981 Harley Davidson FLT 1982 Harley Davidson FLT 1983 Harley Davidson FLT 1984...

Jims 3-Hole Crank Pin Jims crank pin is made of 8620 steel with .062 heat treated penetration. Crank pin is 3 oil hole type. FITS Harley Davidson XL 1981 Harley Davidson XL 1982 Harley Davidson XL 1983 Harley Davidson XL...

Jims 3-Hole Crank Pin .001 Oversize Order nuts separately. FITS Harley Davidson FL 1981 Harley Davidson FL 1982 Harley Davidson FL 1983 Harley Davidson FL 1984 Harley Davidson FLST 1986 Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson...

Jims 3-Hole Crank Pin .002 Order nuts separately. FITS Harley Davidson FL 1981 Harley Davidson FL 1982 Harley Davidson FL 1983 Harley Davidson FL 1984 Harley Davidson FLT 1981 Harley Davidson FLT 1982 Harley Davidson FLT 1983 Harley Davidson FLT...

Jims 3-Hole Crank Pin .025 Shorter Crank pin is heat treated 60-62RC to a case depth of .100. A special 180 oiling design will better lubricate the bearing diameter. Threads are inchJ inch type. Pin is .025 shorter taper to...

Jims 3-Hole Crank Pin 1.250 Jims crank pin is made of 8620 steel with .062 heat treated penetration. Crank pin is 3 oil hole type. FITS Harley Davidson XL 1957 Harley Davidson XL 1958 Harley Davidson XL 1959 Harley Davidson...

Jims 3-Hole Crank Pin with 180 Oiling Crank pin has an outer diameter of 1.2495 inch. Order nuts separately. FITS Harley Davidson FL 1981 Harley Davidson FL 1982 Harley Davidson FL 1983 Harley Davidson FL 1984 Harley Davidson FLST 1986...

Jims 35mm Hex Fork Nut Socket Tool Tool has a rubber protector on the inside to prevent damage to chrome nut. Tool will clear most bars. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0670.pdf FITS Harley Davidson Fx 1973 Harley Davidson Fx 1974 Harley Davidson Fx...

Jims 4th Gear Countershaft Jims 4th gear countershaft for 5-speed stock ratio FITS Harley Davidson FLST 1986 Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST 1989 Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST...

Jims Alternator Rotor Puller Big Twin *NOTE: For use on any 1997-2006 Big Twin models with a 45 amp high output charging system. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1054.pdf FITS Harley Davidson FLT 1997 Harley Davidson FLT 1998 Harley Davidson FLT 1999 Harley Davidson...

Jims Balancer Retainer Tool Hydraulic tensioners are used to keep constant chain tension on the counter balancer system. Without the use of these retaining tools you will not be able to remove or install the balancing system. Use on all...

Jims Brake Caliper Piston Remover Tool This tool prevents any damage to the pistons and the piston bores so seals and wipers can be replaced. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0541.pdf FITS Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002...

Jims Breather Ream Tool Using this tool will repair damaged breather hole to use a .030 oversize breather gear and repair a bad breather hole. Tech Notes: All holes in breather bore will need to be cleared of all chips....

Jims Bushing Remover/Installer Tool Jims bushing remover/installer tool will help remove and install bushings in cam support plate on TC-88 models. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson...

Jims Cam Bearing and Bushing Alignment Tool Any binding of this tool indicates misalignment of cam cover and bushing. When building an engine this is a must have. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0671.pdf FITS Harley Davidson FL 1970 Harley Davidson FL 1971 Harley...

Jims Cam Bearing Installer Tool Jims cam bearing installer tool presses the inner cam bearings smoothly into the right case with the bearings installed to the proper depth. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0660.pdf FITS Harley Davidson FL 1958 Harley Davidson FL 1959 Harley...