Jims TC-88 Connecting Bushing Tool To remove and replace wrist pin bushing without removing connecting rods from crankcase use the Jims TC-88 connector rod bushing tool. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1051.pdf FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST...

Replica Linkert Venturi Removal Tool The 1-3/16 inch collar is used for M-4* ll 16* and 18 carburetors. The 1-3/8 inch collar is used for M-2* 5* 6* 21* 31* 41* 41L 42* 51* 51L 52* 54* 54B 55* 58*...

Flute Tap Tool 3/8 inch-18 Bright Colbalt Flute tap tool 3/8 inch-18 NPT thread features 4 flutes with a bright cobalt finish. Measurements: Overall Length: 2.5625 inches

Fork Cap Wrench Tool Thin design allows for removal of fork plug without disassembling handlebars. Will remove 1-3/8 inch hex fork cap nut on 1/2 inch drive with o-ring insert. FITS Harley Davidson FL 1949 Harley Davidson FL 1950 Harley...

Top End Pushrod Compressor Tool Tool pushes against the top rocker box to allow one hand operation and is for use on 1936-1998 Big Twin and 1957-2003 XL models. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson...

Jims Magnetic Tappet Holder Tool Set Sold as a pair. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson FLST 2003 Harley Davidson FLST 2004 Harley Davidson FLST 2005 Harley...

OE Crankshaft Locking Tool for XL OE crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and torquing of the pinion nut during installation FITS Harley Davidson XL 1991 Harley Davidson XL 1992...

Sifton Pinion Gear Puller Tool Can be used to install gear on 1951-1953 Big Twin 61 inch and 74 inch overhead valve. Tech Notes: Used to install pressed on splined pinion gears on 1939-1953 Big Twin. Used to remove pinion...

Jims Castle Nut Socket 2017-up Softail models requires the castle nut to secure and compress the fork spring. This one piece solid steel socket is designed to secure the joint rod prior to final assembly. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1061.pdf FITS Harley Davidson...

Rod Alignment Plate Parkerized Rod alignment plate features a cast iron construction with a parkerized finish for Big Twin engines. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL...

Rider Tool Kit for 2017 FLT This DIY tool kit will help the rider perform many general maintenence tasks for 2017 FLT models! FITS Harley Davidson FLT 2017

Jims M8 Oil Pump Alignment Tool For the cam support plate along with oil pump gerotors and pump cover to perfectly align with the pinion shaft flat all while properly sealing the oil pump o-ring in the crankcase can be...

Oxygen Sensor Removal Tool The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 7/8 inch wrench or a 3/8 inch drive ratchet. For use on O2 sensors that have 18mm threads and a...

Oxygen Sensor Removal Tool The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 3/8 inch drive ratchet. For use on O2 sensors that have 12mm threads and a 14mm hex. FITS Harley Davidson...

Jims Rolling Buddy Engine Dummy Plate This tool will allow chassis to be moved once the engine has been removed from the frame. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1134.pdf FITS Harley Davidson FLT 1984 Harley Davidson FLT 1985 Harley Davidson FLT 1986 Harley Davidson...

Number Stamp Holder Tool Number stamp tool holds the letter or number stamps from the motor number stamp sets. Measurements: Slot Width: 3/8 inches Tech Notes: Suggested to use with #16-1039 Motor Number Stamp Set. Suggested to use with #16-0453...

Neck Race Remover/Installer Tool Includes the driver handle and 2 piece remover segments. FITS Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST 1989 Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley Davidson...

Piston Pin Support Plate The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1164.pdf FITS Harley Davidson EL 1936 Harley Davidson EL 1937...

Balancer Shaft Retention Pin for TC-88 Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into the balancers sprocket pin holes to prevent turning out of sync...

Jims Ignition Switch and Fork Lock Tool Locates on the ignition switch face nut that holds the switch in place on the frame and lets you remove or install this switch correctly. Tool has a 3/8 inch drive access hole....

Jims Compression Release Valve Tool Order the compression releases separately. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1169.pdf FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson FLST 2003 Harley Davidson FLST 2004 Harley Davidson FLST...

Jims M8 Main Bearing Remover and Installer Jims main bearing remover and installer tool removes the left and right main bearing without damaging the case it also provides correct alignment and depth during installation. For use on M8 models. FITS...

Jims M8 Balancer Scissor Gear Alignment Screw Tool *NOTE: This screw is brightly colored to remind the technician to remove it before sealing the engine case. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley...

Jims Compression Release Valve Set of two. Drill and tap each cylinder head and thread in the self-sealing release valves. Tech Notes: Drill and tap each cylinder head and thread the self-sealing release valves. Recommended to use with #16-1169 Jims...