Cylinder Hold Down Nuts Tool Cylinder hold down nuts tool are used to hold down cylinders during service. Allows motor to be turned over with heads off. FITS Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002...

Clutch Drum Locking Tool Black Drum hub locking tool is used to safely remove the clutch hub and motor nuts and features a black finish. For 1941-1984 Big Twin 4-speed models only FITS Harley Davidson EL 1941 Harley Davidson EL...

Big Twin Rotating / Tilt Engine Stand *NOTE: Customer must install washers and/or bushings not included at pivot points behind knobs to secure motor for alternate tilt angles.*NOTE: Bolts to mount engine not included. Allen cap screws has a 7/16...

Sifton 3 Piece Factory Tool Set The precision reaming of new wrist pin bushings can be accomplished with this tool set. *NOTE: The wrist pin bushing reamer tool is used to secure the rod while performing the reaming operation. The...

Oil Filter Wrench Tool Oil filter wrench tool removes oil filter and drain plug

Gear Alignment Tool We recommends assembling the camplate oil pump camshaft etc together on the bench lining up oil pump gear flats with crankshaft flats and installing the complete assembly into the camchest as one complete unit. This procedure has...

Crimp Tool Deutsch crimp tool for use with all solid type Deutsch terminals.

EL Clutch Tool Set 1936-40 EL clutch tool set includes nut tool and puller tool. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson U 1937...

4-3/4 inch Cross Arm Puller Tool Use any size bolt to pull gears and sprockets that have 2 tapered holes or use with a bearing separator. Tech Notes: Suggested to use bearing separator #16-0602

Engine Stand *NOTE: Does not use an auto engine stand. Measurements: Bottom to top Height: 8-1/4 inches FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson...

Transmission Work Stand Transmission work stand tool features a cast iron construction. Tool is designed to true stock style fly wheels 10 inch swing right side 6 inch swing left side 18 inch maximum center to center. FITS Harley Davidson...

Engine Stand Engine stand measures 15-1/4 inch from the plate to the front holes. *NOTE: Does not use an auto engine stand. FITS Harley Davidson XL 1952 Harley Davidson XL 1953 Harley Davidson XL 1954 Harley Davidson XL 1955 Harley...

Big Twin Engine Stand Base is 2 flat steel plates for mounting to bench. *NOTE: Does not use an auto engine stand. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley...

Terminal Removal Tool Delphi universal terminal removal tool works with AMP multilock and Delphi line up connectors.

Left Rear Lower Motor Mount Bolt Nut Wrench Tool Left rear lower motor mount bolt nut wrench tool. Allows removal and installation of left rear motor mount bolt nut without removing the inner primary cover. FITS Harley Davidson FL 1948...

Spark Plug Wire Tool Spark plug wire tool strips 7 and 8mm ignition wires and crimps spark plug and distributor terminals.

TC-88A Engine Stand Tool Engine stand stool for a TC-88 engine. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson FLST 2003 Harley Davidson FLST 2004 Harley Davidson FLST 2005...

Sifton Oil Pump Check Valve Ball Re-Seater Tool *NOTE: Includes 2 threaded pilot collars. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson FL 1941 Harley...

Mini Motorcycle Lift Tool Mini bike life tool has a wide stance and fully rubberized top plate features Road Warrior bright orange finish with a rubber padded top. V-Twin exclusive! Measurements: Width: 5-9/10 inches

Replacement Threaded Lift Rod Replacement threaded lift rod is for V-Twin #16-0529* Mini Motorcycle Lift Tool. Tech Notes: Required to use with #16-0529 Mini Motorcycle Lift Tool. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0530.pdf

Connecting Rod Bushing Tool Set Sold as a 5 piece set. Patch can easily be ironed or sewn on. *NOTE: When using an electric iron to apply the patch to clothing NEVER use steam. Patch can be sewn on after...

Mini Motorcycle Lift Tool Mini motorcycle lift tool.

Jims Brake Caliper Piston Remover Tool This tool prevents any damage to the pistons and the piston bores so seals and wipers can be replaced. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0541.pdf FITS Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002...

Engine Stand Use with an auto engine stand which must be purchased separately. Not for use with TC-88B engines. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940...