Motor Number Stamp Set Sold as a 29 piece set. Set has many variations of numbers letters and shape combinations. Measurements: Letter/Number Size: 3/16 inches Tech Notes: Suggested to use with #16-1147 Number Stamp Holder Tool. FITS Harley Davidson FL...

Valve Guide Seal Installation Tool Kit Kit is manufactured from high strength 6061-T6 aluminum for increased durability when compared to toeher plastic installation tools. Kit includes four tools for various or separate applications. Kit features precise fitment onto the seal...

Valve Guide Seal Installation Tool Tool features precise fitment onto the seal outer diameter to help the builder center the seal over the valve guide to allow an easier seal. Radiused top striking surface reduces the liklihood of a burr...

Valve Guide Seal Installation Tool Tool features precise fitment onto the seal outer diameter to help the builder center the seal over the valve guide to allow an easier seal. Radiused top striking surface reduces the liklihood of a burr...

Valve Guide Seal Installation Tool Tool features precise fitment onto the seal outer diameter to help the builder center the seal over the valve guide to allow an easier seal. Radiused top striking surface reduces the liklihood of a burr...

Valve Guide Seal Installation Tool Tool features precise fitment onto the seal outer diameter to help the builder center the seal over the valve guide to allow an easier seal. Radiused top striking surface reduces the liklihood of a burr...

Brake Pedal Locking Tool Locking tool is used to lock brake pedals on 1958-1969 FL models. Tool fits over pin on brake plate. FITS Harley Davidson FL 1958 Harley Davidson FL 1959 Harley Davidson FL 1960 Harley Davidson FL 1961...

FXSTS Fork Stem Bearing End Play Adjusting Tool Adjust the steering stern adjuster nut to allow for proper neck bearing end play. Three prong socket 3/8 inch drive with a pass through hole in the center allows for precise neck...

Cylinder Hold Down Nuts Tool Cylinder hold down nuts tool are used to hold down cylinders during service. Allows motor to be turned over with heads off. FITS Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002...

Clutch Drum Locking Tool Black Drum hub locking tool is used to safely remove the clutch hub and motor nuts and features a black finish. For 1941-1984 Big Twin 4-speed models only FITS Harley Davidson EL 1941 Harley Davidson EL...

Big Twin Rotating / Tilt Engine Stand *NOTE: Customer must install washers and/or bushings not included at pivot points behind knobs to secure motor for alternate tilt angles.*NOTE: Bolts to mount engine not included. Allen cap screws has a 7/16...

Sifton 3 Piece Factory Tool Set The precision reaming of new wrist pin bushings can be accomplished with this tool set. *NOTE: The wrist pin bushing reamer tool is used to secure the rod while performing the reaming operation. The...

Oil Filter Wrench Tool Oil filter wrench tool removes oil filter and drain plug

Gear Alignment Tool We recommends assembling the camplate oil pump camshaft etc together on the bench lining up oil pump gear flats with crankshaft flats and installing the complete assembly into the camchest as one complete unit. This procedure has...

Crimp Tool Deutsch crimp tool for use with all solid type Deutsch terminals.

EL Clutch Tool Set 1936-40 EL clutch tool set includes nut tool and puller tool. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson U 1937...

4-3/4 inch Cross Arm Puller Tool Use any size bolt to pull gears and sprockets that have 2 tapered holes or use with a bearing separator. Tech Notes: Suggested to use bearing separator #16-0602

Engine Stand *NOTE: Does not use an auto engine stand. Measurements: Bottom to top Height: 8-1/4 inches FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson...

Transmission Work Stand Transmission work stand tool features a cast iron construction. Tool is designed to true stock style fly wheels 10 inch swing right side 6 inch swing left side 18 inch maximum center to center. FITS Harley Davidson...

Engine Stand Engine stand measures 15-1/4 inch from the plate to the front holes. *NOTE: Does not use an auto engine stand. FITS Harley Davidson XL 1952 Harley Davidson XL 1953 Harley Davidson XL 1954 Harley Davidson XL 1955 Harley...

Big Twin Engine Stand Base is 2 flat steel plates for mounting to bench. *NOTE: Does not use an auto engine stand. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley...

Terminal Removal Tool Delphi universal terminal removal tool works with AMP multilock and Delphi line up connectors.

Left Rear Lower Motor Mount Bolt Nut Wrench Tool Left rear lower motor mount bolt nut wrench tool. Allows removal and installation of left rear motor mount bolt nut without removing the inner primary cover. FITS Harley Davidson FL 1948...

Spark Plug Wire Tool Spark plug wire tool strips 7 and 8mm ignition wires and crimps spark plug and distributor terminals.