Engine Stand Use with an auto engine stand which must be purchased separately. Not for use with TC-88B engines. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940...

Even Pull Transmission Adjuster Kit For use on late style transmission assembly in a rigid frame. Instructions: http://www.vtwinmfg.com/Instructions/17/17-6655.pdf

Evolution Adjustable Pushrod Kit Lifters are e-z install. *NOTE: The longest is the front exhaust next is the front intake and the other 2 go in the rear cylinder head. Tech Notes: Does not require removal of gas tank rocker...

Evolution Cylinder and Piston Kit Black They are ready to run and will require break-in as suggested in the appropriate shop manual. Order gasket set separately. *NOTE: Install pistons with raised bars or on wrist pin area towards the sprocket...

Evolution Cylinder and Piston Kit Silver They are ready to run and will require break-in as suggested in the appropriate shop manual. Order gasket set separately. *NOTE: Install pistons with raised bars or on wrist pin area towards the sprocket...

Evolution Rocker Box Wrench Tool Evolution rocker box wrench tool FITS Harley Davidson FLST 1986 Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST 1989 Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley...

Evolution Tappet Block Set Chrome Each tappet bore is precisioned honed to 0.8435 inch. Sold as a pair Tech Notes: Order gasket kit #15-1542 FITS Harley Davidson FLST 1986 Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST...

Exhaust Bracket Wrench This exhaust bracket wrench is used to remove or install front exhaust bracket bolts. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson FLST 2003 Harley Davidson...

Exhaust Pipe Retaining Ring Tool This tool makes it easy to install the 65325-83A ring in seconds without twisting the ring or scratching the exhaust pipe. No more inchflying inch and incheye popping inch retaining rings it's the simple tools...

Exhaust Stud Kit Exhaust Stud Kit includes 4 studs and 4 stainless steel flanged nuts. FITS Harley Davidson FLST 1986 Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST 1989 Harley Davidson FLST 1990 Harley Davidson FLST 1991...

Exhaust Stud Kit Exhaust stud kit includes four 5/16 inch x 1-3/4 inch studs and four 5/16 inch-24 UNF chrome flanged nuts. The studs have 5/16-18 UNC thread on one end and 5/16-24 UNF thread on the other end. FITS...

Factory Sample 4-Finned FL Cast Cam Cover Cam cover bushings must be checked and fitted (reamed) for final assembly. Check end play as well. Make sure oil passages and oil feed holes in bushings are clear. Tapered screw holes may...

Factory Sample Black Narrow Profile Outer Primary Cover Stock replacement for all 2007-16 FLT models but can be used on all 2014-16 FLT models but requires the purchase of narrow type 2015-up derby cover and primary gasket service gasket kit....

Factory Sample Black Outer Primary Cover This die cast cover is accurately produced with new tooling that is exclusive to V-Twin manufacturing. Order screws starter shaft bushing and gaskets separately. Factory sample cover is a brand new pre-production part but...

Factory Sample Cam Cover Polished Lower mount hole is slotted. Cover is for electric start models. All cam bushings are installed but may need reaming before final installation. Breather sleeve is installed. *NOTE: Hole is slotted for use on cross...

Factory Sample Cam Cover Polished Lower mount hole is slotted for 1977-up models. Cover is for electric start models. The top threaded hole measures 5/8 inch X 11. *NOTE: Lower edge has welding marks and pits where cross fit for...

Factory Sample Chrome 3/4 inch Offset Inner Primary Cover For use with 1994-2003 primary components. Factory sample cover are brand new pre-production parts but have imperfections in the finished surface. Check threaded and bearing holes for excess plating before installation....

Factory Sample Chrome Cam Gearcase Cover Factory sample is a brand new production part but may have imperfections in the finished surface. Check threaded and bearing holes for excess plating before installation. There are no physical defects such as cracks...

Factory Sample Chrome Inner Primary Cover Cover includes 1-1/2 inch bolt spacing located at the transmission mount and mid control hole. Order bearing bushing and seal separately. Factory sample cover are brand new pre-production parts but have imperfections in the...

Factory Sample Chrome Nose Cone Cam Cover For use on models with a side oiling pinion shaft. Factory sample is a brand new production part but may have imperfections in the finished surface. Check threaded and bearing holes for excess...

Factory Sample Chrome Outer Primary Cover This die cast cover is accurately produced with new tooling that is exclusive to V-Twin manufacturing. *NOTE: Requires a 5-hole berby cover. Can also be used on 1984-1998 FLT models but requires a 1999-up...

Factory Sample Chrome Outer Primary Cover Partially drilled 9th hole is at the 6 O'clock position below the derby cover. Order starter bearing separately. Factory sample cover are brand new pre-production parts but have imperfections in the finished surface. Check...

Factory Sample Chrome Outer Primary Cover *NOTE: Does not feature the bearing installed. Factory sample cover are brand new pre-production parts but have imperfections in the finished surface. Check threaded and bearing holes for excess plating before installation. *NOTE: Does...

Factory Sample Chrome Outer Primary Cover Order screws separately. Factory sample cover are brand new pre-production parts but have imperfections in the finished surface. Check threaded and bearing holes for excess plating before installation. *NOTE: Does not include any hardware....