Mainshaft Race .002 Jims 4-speed transmission mainshaft race .002 FITS Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson FL 1941 Harley Davidson FL 1942 Harley Davidson FL 1943 Harley Davidson...

Mainshaft Race .005 Jims transmission mainshaft race .005 FITS Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson FL 1941 Harley Davidson FL 1942 Harley Davidson FL 1943 Harley Davidson FL...

Mainshaft Race .010 Jims transmission mainshaft race .010 FITS Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson FL 1941 Harley Davidson FL 1942 Harley Davidson FL 1943 Harley Davidson FL...

Mainshaft Race Standard Jims transmission mainshaft race standard Measurements: Inner Diameter: 1.8802 inches FITS Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL 1940 Harley Davidson FL 1941 Harley Davidson FL 1942 Harley Davidson...

Mainshaft Seal Remover and Installer It will push the seal in as flat and straight as possible to .050 below housing for a no leak fit. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley...

O2 Sensor Wrench Tool Jims O2 wrench allows removal and installation of O2 sensors without removal of exhaust pipes. Instructions: http://www.vtwinmfg.com/Instructions/16/16-2755.pdf FITS Harley Davidson FXD 2012 Harley Davidson FXD 2013 Harley Davidson FXD 2014 Harley Davidson FXD 2015 Harley Davidson...

O2 Sensor Wrench Tool Jims O2 wrench allows removal and installation of O2 sensors without removal of exhaust pipes. Instructions: http://www.vtwinmfg.com/Instructions/16/16-2756.pdf FITS Harley Davidson FXST 2012 Harley Davidson FXST 2013 Harley Davidson FXST 2014 Harley Davidson FXST 2015 Harley Davidson...

Oil Pump Feed Idler Gear Oil pump feed idler gear is made from solid billet steel By installing this gear you will have an increase over 5% in pressure as well as an increase of 5% in volume. FITS Harley...

Oil Pump Snap Ring Installer The oil pump snap ring installer makes it easy to install outer snap ring on oil pump shafts without stretching the ring. Use on Big Twin oil pumps. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0889.pdf FITS Harley Davidson EL 1936...

Pinion Bushing Drill Jig Tool The Jims pinion bushing jig tool allows the installation and drilling of a dowel pin to factory location supplied with #31 drill by Jims. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1780.pdf FITS Harley Davidson FL 1954 Harley Davidson FL 1955...

Pinion Bushing Drill Jig Tool The cam and pinion bushing drill jig tool allows the installation and drilling of a dowel pin to factory location. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson...

Pinion Bushing Puller Tool This pinion bushing puller tool is used to remove the pinion bushing from the cam cover. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1822.pdf FITS Harley Davidson FL 1954 Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley...

Pinion Gear Puller Tool Kit Can be used to install gear on 1951-1953 Big Twin 61 inch and 74 inch overhead valve. Tech Notes: Used to install pressed on splined pinion gears on 1939-1953 Big Twin Used to remove pinion...

Pinion Gear Shaft Jims pinion gear shaft FITS Harley Davidson Chief 1933 Harley Davidson Chief 1934 Harley Davidson Chief 1935 Harley Davidson Chief 1936 Harley Davidson Chief 1937 Harley Davidson Chief 1938 Harley Davidson Chief 1939 Harley Davidson Chief 1940...

Pinion Shaft Yellow Size Gear Pinion shaft gear is yellow size the smallest size gear. FITS Harley Davidson FL 1954 Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley Davidson FL 1959...

Piston Pin Alignment Tool The piston pin align tool is used to check straightness of the rod without removing rods from case. Tool is 4-1/2 inch long. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938...

Piston Pin Support Plate The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1164.pdf FITS Harley Davidson EL 1936 Harley Davidson EL 1937...

Primary Locking Tool The Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torquing of clutch hub and engine nut. FITS Harley Davidson FXD 2006 Harley...

Receptacle Extractor Tool for Molex Style Connector Receptacle extractor tool removes Molex style connector

Right Side Case Race .005 .005 oversize right side case race is machined and ground to factory specifications. FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley Davidson G 1942 Harley Davidson G 1943 Harley...

Right Side Case Race Standard Standard right side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch . FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley...

Rocker Arm Bushing and Roller Bearing Puller This rocker arm roller bearing puller Instructions: http://www.vtwinmfg.com/Instructions/16/16-1848.pdf

Rocker Arm Bushing Reamer Tool The Jims rocker arm bushing reamer tool is used to ream rocker bushings to a factory fit of .0007 inch-.0012 inch in line with each other. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1804.pdf

Rocker Arm Shaft Jims rocker arm shaft has an outer diameter at the big end of .937 inch and the small end of .434 inch. Measurements: Outer Thread Pitch: 7/16 inches -20 FITS Harley Davidson FL 1966 Harley Davidson FL...