Shaft Turning Tool This Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2 inch ratchet or impact driver. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1378.pdf FITS Harley Davidson FLST 2007 Harley Davidson FLST 2008...

Shoulderless Valve Guide Driver Tool Handle Only Use driver handle to remove or install valve guides. Installation of shoulderless guides requires correct installation socket. Tech Notes: Recommended to use with #16-0321 Valve Guide Installer Tool FITS Harley Davidson FLST 1999...

Shoulderless Valve Guide Installer Tool Remover handles are used as handle for installer tool must be ordered separately. Use driver handle to remove or install valve guides. Installation of shoulderless guides requires correct installation socket. Tech Notes: Recommended to use...

Snap Ring Remover Tool You can replace the snap ring in Big Twin cases without the fear of gouging the aluminum on the cases. FITS Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley Davidson FLST...

Solid Tappet Assembly .005 Order adjuster screws and nuts separately. FITS Harley Davidson FL 1948 Harley Davidson FL 1949 Harley Davidson FL 1950 Harley Davidson FL 1951 Harley Davidson FL 1952

Solid Tappet Assembly .005 Jims .005 oversize solid tappets can be only used with adjustable pushrods. FITS Harley Davidson XL 1986 Harley Davidson XL 1987 Harley Davidson XL 1988 Harley Davidson XL 1989 Harley Davidson XL 1990 Harley Davidson XL...

Sprocket Flywheel Nut Socket Tool Jims sprocket flywheel nut socket features a low profile to give 100% nut contact machined flat at nut receiving end to eliminate rounding off the nut. Fits 3/4 inch Drive. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1812.pdf FITS Harley Davidson...

Sprocket Shaft Bearing and Seal Installation Tool Adapter Allows for installation of Timken bearings and roller bearing race assembly onto the sprocket shaft. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1364.pdf FITS Harley Davidson FLST 2007 Harley Davidson FLST 2008 Harley Davidson FLST 2009 Harley Davidson...

Sprocket Shaft Bearing Installer Tool Tool is 2.500 inch long. Tech Notes: Required to use with #16-1761 Sprocket shaft bearing installation tool FITS Harley Davidson XL 1977 Harley Davidson XL 1978 Harley Davidson XL 1979 Harley Davidson XL 1980 Harley...

Sprocket Shaft Bearing Installer Tool This tool also can be used to install the bearing until tool runs out of threads. Tool is 2.060 inch long. Tech Notes: Required to use with #16-1760 sprocket shaft bearing installation tool Instructions: http://www.vtwinmfg.com/Instructions/16/16-1761.pdf...

Sprocket Shaft Bearing Tool *NOTE: Includes 1 collar. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1836.pdf FITS Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley Davidson FL 1959 Harley Davidson FL 1960 Harley Davidson FL 1961 Harley...

Sprocket Shaft Bearing Tool If using this tool on a 1977-up XL we require using the 2.500 inch and 2060 inch sprocket shaft bearing installer tool. Tech Notes: Required to use #16-1760 2.500inch Sprocket Shaft Bearing Installation Tool on 1977-up...

Sprocket Shaft Nut Jims sprocket shaft nut is 1-1/8 inch-16 for taper end shaft. FITS Harley Davidson FL 1972 Harley Davidson FL 1973 Harley Davidson FL 1974 Harley Davidson FL 1975 Harley Davidson FL 1976 Harley Davidson FL 1977 Harley...

Sprocket Shaft Seal and Lock Installer Sprocket shaft seal wrench tool installs and removes bearing nut on Big Twin models. Instructions: http://www.vtwinmfg.com/Instructions/16/16-0888.pdf FITS Harley Davidson FL 1955 Harley Davidson FL 1956 Harley Davidson FL 1957 Harley Davidson FL 1958 Harley...

Sprocket Shaft Seal Install Tool Use with a bearing tool to help install seal. Tech Notes: Order #16-0140 or #16-1836 bearing tool Instructions: http://www.vtwinmfg.com/Instructions/16/16-1754.pdf FITS Harley Davidson FL 1970 Harley Davidson FL 1971 Harley Davidson FL 1972 Harley Davidson FL...

Standard Case Race Left Side Left side case race is machined and ground to factory specifications. Race has an outer diameter of 1.753 inch. FITS Harley Davidson G 1939 Harley Davidson G 1940 Harley Davidson G 1941 Harley Davidson G...

Standard Hydraulic Tappet Tappets are without internals. Order hydraulic unit separately. **NOTE: Tappet adjustment will make the pushrod tight. Wait 5-15 minutes or longer to fully bleed off the hydraulic tappet. Make sure engine is not rotated while pushrods are...

Standard Hydraulic Tappet Assembly Jims big axle power glide tappet assembly. Tappets have an outer diameter of .731 inch and are for Shovelhead engines. Instructions: http://www.vtwinmfg.com/Instructions/10/10-0642.pdf FITS Harley Davidson FL 1966 Harley Davidson FL 1967 Harley Davidson FL 1968 Harley...

Standard Hydrosolid Tappet Assembly Order adjuster screws or nuts where necessary. **NOTE: Tappet adjustment will make the pushrod tight. Wait 5-15 minutes or longer to fully bleed off the hydraulic tappet. Make sure engine is not rotated while pushrods are...

Standard Power Glide Tappet Assembly Tappet has outer diameter is .9035 inch. Order adjuster screws or nuts where necessary. FITS Harley Davidson XL 1991 Harley Davidson XL 1992 Harley Davidson XL 1993 Harley Davidson XL 1994 Harley Davidson XL 1995...

Standard Solid Tappet Assembly Order adjuster screws and nuts separately. Measurements: Overall Length: 3.430 inches FITS Harley Davidson FL 1948 Harley Davidson FL 1949 Harley Davidson FL 1950 Harley Davidson FL 1951 Harley Davidson FL 1952 Harley Davidson FL 1953...

Standard Solid Tappet Assembly Jims standard solid tappets can only be used with adjustable pushrods. Tappet has an outer diameter of .8425 inch. FITS Harley Davidson XL 1986 Harley Davidson XL 1987 Harley Davidson XL 1988 Harley Davidson XL 1989...

Starter Ring Gear Rivet Fixture Tool This tool removes the starter ring gear rivets from clutch shells. FITS Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley Davidson FLST 1993 Harley Davidson FLST 1994 Harley Davidson...

Swingarm Assembly Tool The swingarm assembly tool removes and installs swingarm pivot components. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1734.pdf FITS Harley Davidson FLT 1980 Harley Davidson FLT 1981 Harley Davidson FLT 1982 Harley Davidson FLT 1983 Harley Davidson FLT 1984 Harley Davidson FLT 1985...