MOTION PRO Tappet Adjuster Tool - 3x8 mm 08-0732 Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw, Allows precise valve lash adjustment without disturbing the setting when...

MOTION PRO Ear Clamps with Pincher Tool - Fuel Line - Stepless - Assortment 12-0083 Convenient kit includes 80 pieces of hardware, a Motion Pro side jaw pincher tool and a convenient fuel line clamp size chart packed in a...

MOTION PRO Tappet Adjuster Tool - 4x10 mm 08-0734 Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw, Allows precise valve lash adjustment without disturbing the setting when...

MOTION PRO Compression Adjustment Tool 11-0118 Allows for easy adjustments to compression damping without the use of tools, Designed to fit motorcycles '06 to present fitted with KYB AOS/SSS forks, Requires 10 mm handlebar clearance above top of fork cap,...

MOTION PRO Pushrod Tool - Harley-Davidson 08-0744 Flat portion of tool fits under the cylinder head while cupped end fits over the bell in the tube and then compresses the spring allowing for easy access to the spring cap retainer,...

MOTION PRO Compression Bolt Removal Tool - WP 4860 MXMA CC Fork 08-0436 Also works for installation and removal of compression unit on RH fork on WP AER 48 mm fork, commonly found on '19-'23 KTM SX/F, XC/F models, Allows...

MOTION PRO Deluxe Piston Pin Puller Tool 08-0472 Works on both full skirt and short skirt (slipper) pistons, Fits all piston pins from 12 mm (1/2") to 24 mm (1"), Non-marring aluminum pin adapters, Interchangeable piston adapters

MOTION PRO Pincher Tool - Side Jaw/Ear Clamp - Stepless? 12-0073 Side jaw design for use where space is restricted, Used to install Stepless? ear clamps

MOTION PRO Valve Stem Seal Tool - Installation - 4 mm 08-0507 Contoured design in bottom of handle cradles and protects the delicate inner lip of the valve stem seal while directing tool force to the sturdy outer rim, Slim...

MOTION PRO Seal/Bearing Retainer Tool - Honda 08-0227 Precision design prevents damage to the retainer ring after peened stakes have been removed by drilling, To remove and replace the rear wheel bearing/seal retainer ring, part number 41231-429-000 and 41231-286-000, Design...

MOTION PRO Seal/Bearing Retainer Tool - 44 mm - CR 08-0228 Precision design prevents damage to the retainer ring after peened stakes have been removed by drilling, 44 mm, to remove and replace the rear wheel bearing/seal retainer ring, part...

MOTION PRO Pilot Screw Adjustment Tool - 17" 08-0119 Designed for hard-to-reach air/fuel mixture screws with a straight-slot blade tip that can be rotated by rotating the handle, 110? angled head extends reach 1"

MOTION PRO Oil Filter Tool - Puler - KTM 08-0400 Conical point screw pierces and grabs the sheet metal end cap on filter, Reduces potential damage to the engine cases, For easy removal of recessed KTM oil filters, Contoured handle...

MOTION PRO Extension Socket Tool - 13/16" 08-0291 Allows the Motion Pro? Ratchet Spark Plug Wrench to be used on recent models where the water neck prevents the use of the wrench alone, Designed to fit in limited space on...

MOTION PRO Hose Removal Tool 08-0646 Facilitates removal of fuel and cooling system hoses, One end is used to loosen stuck hose, the other end assists in pulling the hose off the fitting, Reduces the possibility of damage to hoses...

MOTION PRO Screw - Tappet Tool - Oil Filter 08-0339 O-ring design retains the tool in wrench or socket while flange design allows downward force to be applied to tool, Designed for use with 7/16" combination wrench to allow for...

MOTION PRO Adapter Tool Kit 08-0249 Adapter kit does not allow two stroke timing kit to be installed on Yamaha RD two stroke twins when the engine is in the frame but does allow adapter kit with two stroke timing...

MOTION PRO Hex Bit Tool - 3 mm x 4 mm 08-0382 Fits in Motion Pro? Deep Socket and T-Handle Wrench, Rubber O-ring will keep bit securely in place

MOTION PRO Seal/Bearing Retainer Tool - 47 mm - CR 08-0256 To remove and replace the rear wheel bearing / seal retainer rings, part numbers 41231-KZ4-J20 and 41231-KS6-700, Precision design prevents damage to the retainer ring after peened stakes have...

MOTION PRO Bearing Removal Tool - Wheel - 25 mm 08-0267 Heat treated for durability and long service life

MOTION PRO Float Bowl Tool - 17 mm 08-0366 Can also be used as a high-speed compression adjustment wrench for most Showa, KYB, and WP rear shocks, Designed to remove 17 mm float bowl drain plugs and can be carried...

MOTION PRO Valve Shim Tool - Valve Adjuster - Suzuki 08-0017 Holds valve spring bucket down so adjusting shims can be removed, For adjusting valve clearance on twin cam models, Manufactured from hardened alloy steel

MOTION PRO Fork Spring Tool - Springer/Front Fork - Harley Davidson 08-0144 Assists in the disassembly and assembly of springer-type front forks on Harley-Davidson motorcycles, Made in the USA

MOTION PRO T-Handle Tool - Mini-Pro - Compact - 6 mm 08-0401 Compact size for easy access and easy transport, Chrome-vanadium tool steel shaft, Lifetime limited warranty, 6-3/4" shaft length, 6 mm drive