Legacy 3.8 Gallon Gas Tank Order gas cap separately. *Note: UPS may consider this part as packaged inchoversize inch for shipment as compared to the actual weight which will result in higher shipping costs. Tech Notes: Suggested to use with...

FXST Gas Tank Raw Softail breakout FXST style gas tank features a raw finish. FITS Harley Davidson FLST 2012 Harley Davidson FLST 2013 Harley Davidson FLST 2014 Harley Davidson FLST 2015 Harley Davidson FLST 2016 Harley Davidson FLST 2017 Harley...

Emblem Mount Screws for Gas Tank Slightly shorter than OE for aftermarket emblems and tanks. Sold as a pack of 10. Screws measure 6-32 x 1/4 inch length like OEM #2070. Tech Notes: Suggested to use with #37-8826 Emblem Mount...

M8 Stretch 5.00 Gallon Gas Tank Raw Check the tank for flaws and fit before painting. Do not grind or sand the seams or joints. Clean the inside of the tank. It is suggested to pressure test and use a...

M8 Pirate 5.00 Gallon Gas Tank Raw Check the tank for flaws and fit before painting. Do not grind or sand the seams or joints. Clean the inside of the tank. It is suggested to pressure test and use a...

M8 Bobbed Gas Tank Raw Features bolt on installation with original hardware. Check the tank for flaws or fit before painting. Do not grind or sand the seams or joints. Clean the inside of the tank. It is suggested to...

Chopper Peanut Gas Tank Mount Tab Set Raw For use on small single piece gas tanks. Sold as a 2 piece set. *NOTE: Must be welded on and drilled for mounting tank on top of frame tube. Tech Notes: Suggested...

M8 Bobbed Gas Tank Raw Steel Bobbed gas tank features a raw finish with a 5.3 gallon capacity for M8 models. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST 2021 Harley Davidson...

Extended Gas Tank Smooth 4.2 Gallon One piece smooth extended Gas Tank with a fuel capacity of 4.2 gallons. Tank uses 22mm petcock and it has an arched bottom. Measurements: Width: 16 inches FITS Harley Davidson FLST 1986 Harley Davidson...

Fat Bob Gas Tank Kit with 3.5 Gallon Tank set accepts a cateye dash only. The lower bracket is inchC inch shaped. Tank may require fuel rod alignment before installation of shut off assembly. Check the tank for flaws or...

Fat Bob Gas Tank Kit 3.5 Gallon Kit features provisions to accept early caps reserve shut off rod and tow or three light dash not included. For use with hand shift applications and accepts 3/8 inch NPT petcock with male...

FL Fat Bob Gas Tank Kit 3.5 Gallon For hand shift applications. Accepts a 3/8 inch NPT petcock with male threads not included. Opening is left side forward on tank. Features provisions to accept early caps reserve shut off rod...

M8 Gas Tank Mount Kit Kit includes two 3/8 inch-18 x 4.25 inch screws four ferrous washers four bushings four grommets and two acorn nuts with lock. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020...

M8 Sporty 2.9 Gallon Gas Tank Raw Steel Medium Mount Accepts bung type vented gas cap. Check the tank for flaws or fit before painting. Do not grind or sand the seams or joints. Clean the inside of the tank....

M8 Sporty 3.6 Gallon Gas Tank Raw Steel High Mount Includes an alloy screw in type type vented gas cap. Check the tank for flaws or fit before paiting. Do not grind or sand the seams or joints. Clean the...

M8 Sporty 3.2 Gallon Gas Tank Raw Steel Low Mount *NOTE: Fuel pump will have to be hand fitted for installation. Check the tank for flaws or fit before painting. Do not grind or sand the seams or joints. Clean...

M8 Bobbed Gas Tank Raw Tank is bolt on style like the original. Does not have provision for gauge. Tank will require primer and minor filling before the final paint finish. Re-intall original EFI fuel pump. Tank accepts right side...

Mount Strips for Gas Tank Emblems Emblem mounts may have to be contoured to match tank curve before installation. Order screws separately. Tech Notes: Suggested to use #37-8826 screws. Suggested to use #38-6670 emblems.

Factory Sample Replica Roadster 4.5 Gallon Gas Tank Check the tank for flaws and fit before painting. The tank requires sanding and primer before painting. Do not grind or sand the seams or joints. It is suggested to pressure test...

Factory Sample FXD Stock Shape 5.1 Gallon Gas Tank Raw Check the tank for flaws and fit before painting. Do not grind or sand the seams or joints. The fuel line fitting should be masked or plugged for easy installation...

Factory Sample Bobbed 5.1 Gallon Gas Tank The center to center distance of the front and rear mount is 20 inch. The thread size for the hole next to the petcock hole measures 5/16 inch-24 *NOTE: Tank requires sanding and...

Factory Sample Bobbed 5.1 Gallon Gas Tank Check the tank for flaws and fit before painting. Tank requires sanding and primer. Do not grind or sand the seams or joints. The fuel line fitting should be masked or plugged during...

Factory Sample King 3.2 Gallon Gas Tank *NOTE: Has external threads for the petcock. Check the tank for flaws and fit before painting. Do not grind or sand the seams or joints. Check the petcock opening making sure the petcock...

Factory Sample Replica Sportster 2.4 Gallon Gas Tank High tunnel stock style tank features stock mounts and filler neck. Check the tank for flaws and fit before painting. Do not grind or sand the seams or joints. Clean the inside...