Jims FLT Inner Primary Shifter Shaft Bushing Tool *NOTE: Using this tool can remove and install the bushings in approximately 20 minutes. FITS Harley Davidson FLT 1985 Harley Davidson FLT 1986 Harley Davidson FLT 1987 Harley Davidson FLT 1988 Harley...

Jims Swingarm Bearing Installer Tool A remover has been added to press the spacer out of the bearing. *NOTE: Swingarm bearings must be installed and aligned correctly to avoid unsafe handling and ensure control of the motorcycle. FITS Harley Davidson...

Jims Steering Head Race Installer Tool Jims steering head race installer tool features smaller and tapered drivers ensuring optimal alignment and a fully installed depth. FITS Harley Davidson FLT 2014 Harley Davidson FLT 2015 Harley Davidson FLT 2016 Harley Davidson...

Jims Fork Cap Installation Tool Jims fork cap installation tool for use on 49mm forks allows the installation of the fork tube caps on the motorcycle without removing other parts FITS Harley Davidson FLT 2014 Harley Davidson FLT 2015 Harley...

Jims Fork Cap Allen Socket Tool Jims fork cap large allen head socket tool for use on 49mm forks. FITS Harley Davidson FLT 2014 Harley Davidson FLT 2015 Harley Davidson FLT 2016 Harley Davidson FLT 2017 Harley Davidson FLT 2018...

Jims M8 Engine Stand Jims engine stand needed for any powertrain work is built from .125 inch steel and powdercoated blue. For M8 models. FITS Harley Davidson FLT 2017 Harley Davidson FLT 2018 Harley Davidson FLT 2019 Harley Davidson FLT...

Jims M8 Cylinder Torque Plate Kit This Jims cylinder torque plate tool kit simulates stress conditions when boring and honing cylinders. For M8 models. FITS Harley Davidson FLT 2017 Harley Davidson FLT 2018 Harley Davidson FLT 2019 Harley Davidson FLT...

Jims M8 Left Main Seal Removal Tool Jims left main seal removal tool is for M8 models. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1200.pdf FITS Harley Davidson FLT 2017 Harley Davidson FLT 2018 Harley Davidson FLT 2019 Harley Davidson FLT 2020 Harley Davidson FLT 2021...

Jims XL Primary Locking Bar By shifting the transmission into top gear (direct drive) allows for removal installation and accurate torque when tightening the final drive front sprocket/pulley nut. FITS Harley Davidson XL 2004 Harley Davidson XL 2005 Harley Davidson...

Receptacle Extractor Tool for Molex Style Connector Receptacle extractor tool removes Molex style connector

Jims M8 Flywheel Locking Tool Jims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the engine and locks the crankshaft when doing service work....

Jims M8 FXST Engine Stand Jims M8 FXST engine stand needed for any powertrain work is built from .125 inch steel and powdercoated blue. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST...

Transmission Main Gear Nut Wrench This tool is designed to remove and install the right handed nut that holds on the transmission pulley. The inner collar is designed to be threaded onto the mainshaft. This tool is designed to stop...

Motor Number Stamp Set Sold as a 22 piece set. Set has many variations of numbers letters and shape combinations. Measurements: Number Stamp Size: 3/16 inches Tech Notes: Suggested to use with #16-1147 Number Stamp Holder Tool. FITS Harley Davidson...

1/4 x 24 inch Tap and Die Tool Set Set includes a special tap tool used for repairing or is used for repairing or dressing 1/4 inchx 24 TPI and the corresponding tap tool. FITS Harley Davidson EL 1936 Harley...

V-Twin Ignition Switch Alignment Tool This tool gives the ignition switch knob the alignment it needs to extend the life of the ignition switch housing. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1265.pdf FITS Harley Davidson FLT 2014 Harley Davidson FLT 2015 Harley Davidson FLT 2016...

Rear Sprocket Rivet Tool This is a 5 piece set. Includes drum holder drum collar spacer (for Sportster drums only) rivet set and hollow dowel pin driver. Rivets are not included. FITS Harley Davidson EL 1937 Harley Davidson EL 1938...

Rider Tool Kit 17 piece tool kit. NOTE: Entire kit will fit in oval kidney shaped tool boxes.

TC Beta Engine Stand The Beta engine stand is powder coated steel and clears the rear balancer housing of the Beta style TC case. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST...

4-Speed Transmission Arbor Tool This 4-speed transmission arbor tool is what you need to replace the clutch hub nut to allow test rotation with 1/2 inch drill. FITS Harley Davidson FL 1941 Harley Davidson FL 1942 Harley Davidson FL 1943...

Cam Bearing Puller Tool Tool is designed for hand wrench use. Power driving with an air wrench or too much interference will break the stud. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1271.pdf FITS Harley Davidson FL 1958 Harley Davidson FL 1959 Harley Davidson FL 1960...

Jims Crank Shaft Guide Use this crank shaft guide to spread pinion bearing rollers while reassembling right side engine case on to flywheel assembly. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1281.pdf FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley...

Jims TC-88 Inner Cam Bearing Remover The Jims inner cam bearing remover replaces the inner bearing easily without damage to crankcases and also prevents rollers from falling into the crankcase. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1279.pdf FITS Harley Davidson FLST 1999 Harley Davidson FLST...

Jims TC-88 Crankshaft Rear Bearing Tool This crankshaft bearing tool is designed to remove and repla ce the right crankcase bearing in and out with no damage to crankcase. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson...