Rod Alignment Plate Parkerized Rod alignment plate features a cast iron construction with a parkerized finish for Big Twin engines. FITS Harley Davidson EL 1936 Harley Davidson EL 1937 Harley Davidson EL 1938 Harley Davidson EL 1939 Harley Davidson EL...

Rider Tool Kit for 2017 FLT This DIY tool kit will help the rider perform many general maintenence tasks for 2017 FLT models! FITS Harley Davidson FLT 2017

Jims M8 Oil Pump Alignment Tool For the cam support plate along with oil pump gerotors and pump cover to perfectly align with the pinion shaft flat all while properly sealing the oil pump o-ring in the crankcase can be...

Oxygen Sensor Removal Tool The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 7/8 inch wrench or a 3/8 inch drive ratchet. For use on O2 sensors that have 18mm threads and a...

Oxygen Sensor Removal Tool The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 3/8 inch drive ratchet. For use on O2 sensors that have 12mm threads and a 14mm hex. FITS Harley Davidson...

Jims Rolling Buddy Engine Dummy Plate This tool will allow chassis to be moved once the engine has been removed from the frame. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1134.pdf FITS Harley Davidson FLT 1984 Harley Davidson FLT 1985 Harley Davidson FLT 1986 Harley Davidson...

Number Stamp Holder Tool Number stamp tool holds the letter or number stamps from the motor number stamp sets. Measurements: Slot Width: 3/8 inches Tech Notes: Suggested to use with #16-1039 Motor Number Stamp Set. Suggested to use with #16-0453...

Neck Race Remover/Installer Tool Includes the driver handle and 2 piece remover segments. FITS Harley Davidson FLST 1987 Harley Davidson FLST 1988 Harley Davidson FLST 1989 Harley Davidson FLST 1990 Harley Davidson FLST 1991 Harley Davidson FLST 1992 Harley Davidson...

Piston Pin Support Plate The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1164.pdf FITS Harley Davidson EL 1936 Harley Davidson EL 1937...

Balancer Shaft Retention Pin for TC-88 Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into the balancers sprocket pin holes to prevent turning out of sync...

Jims Ignition Switch and Fork Lock Tool Locates on the ignition switch face nut that holds the switch in place on the frame and lets you remove or install this switch correctly. Tool has a 3/8 inch drive access hole....

Jims Compression Release Valve Tool Order the compression releases separately. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1169.pdf FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST 2001 Harley Davidson FLST 2002 Harley Davidson FLST 2003 Harley Davidson FLST 2004 Harley Davidson FLST...

Jims M8 Main Bearing Remover and Installer Jims main bearing remover and installer tool removes the left and right main bearing without damaging the case it also provides correct alignment and depth during installation. For use on M8 models. FITS...

Jims M8 Balancer Scissor Gear Alignment Screw Tool *NOTE: This screw is brightly colored to remind the technician to remove it before sealing the engine case. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley...

Jims Compression Release Valve Set of two. Drill and tap each cylinder head and thread in the self-sealing release valves. Tech Notes: Drill and tap each cylinder head and thread the self-sealing release valves. Recommended to use with #16-1169 Jims...

Jims M8 Alternator Rotor Remover and Installer Jims high output alternator rotor remover and installer easily removes the rotor while protecting the magnets within it. For use on M8 models. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley...

Jims M8 Camshaft Needle Bearing Remover and Installer This tool holds tighter tolerances which allows for a more precise installation depth. *NOTE: This remover uses the inchJims Style inch remover collet as well as inchJims inch fine threaded installation driver....

Jims M8 Left Main Seal Installer *NOTE: When the seal is installed properly ther will be some bottoming out. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST 2021 Harley Davidson FLST 2022...

Jims M8 Wrist Pin Remover Adapter To save space in the tool box use with Jims TC-88 wrist pin remover tool. Tech Notes: Suggested to use with #16-1276 Jims TC-88 Wrist Pin Remover Tool. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1187.pdf FITS Harley Davidson FLST...

Jims M8 Cylinder Hold Down Nuts Kit There are different threads at each end. Sold 2 per kit. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST 2021 Harley Davidson FLST 2022 Harley...

Jims M8 Valve Spring Compressor Adapter *NOTE: Conical valve spring adapter only to be used with VT #16-1771 Valve Spring Compressor Tool. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST 2020 Harley Davidson FLST 2021 Harley...

Jims M8 Cylinder Head Holder Tool Jims cylinder head holder tool is two sided one side threaded for Twin Cam heads and the other threaded for M8 models. FITS Harley Davidson FLST 1999 Harley Davidson FLST 2000 Harley Davidson FLST...

Jims M8 Countershaft 1st Scissor Gear Alignment Tool *NOTE: it is installed before the scissor gear is removed to maintain alignment of the gear halves under spring pressure. FITS Harley Davidson FLST 2018 Harley Davidson FLST 2019 Harley Davidson FLST...

Jims XL Sprocket Nut Socket Jims XL sprocket nut socket is designed specifically for XL models to remove install and properly tighten the front final drive sprocket/pulley. Instructions: http://www.vtwinmfg.com/Instructions/16/16-1192.pdf FITS Harley Davidson XL 1991 Harley Davidson XL 1992 Harley Davidson...